iglidur® A500 - Material data

Figure 02: Maximum recommended surface pressure dependent on the temperature (120 MPa to +20 °C)

X = Temperature [°C]
Y = Load [MPa]

Figure 03: Deformation under load and temperatures

X = Load [MPa]
Y = Deformation [m/s]

Mechanical properties

Maximum recommended surface pressure represents a mechanical material parameter. Tribological conclusions cannot be drawn from it. With increasing temperatures, the compressive strength of iglidur® A500 bearings decreases. Fig. 02 clarifies this connection.
 
Figure 02 shows the maximum recommended surface pressure of the bearing dependent on the temperature. The combination of high stability and high flexibility acts very positively during vibrations and edge loads. As the wear of the bearing rapidly escalates from pressures of 10 to 20 MPa, we recommend a particularly accurate testing of the application above these limits.

Maximum surface speed

m/s	Rotating	Oscillating	Linear
Constant	0,6	0,4	1
Short-term	1	0,7	2

Permitted surface speeds

iglidur® A500 also permits high surface speeds due to the high temperature resistance. The coefficient of friction rises however by these high rotatary speeds leading to a higher heating up of the bearing. Tests show that bearings made of iglidur® A500 are more wear resistant in pivoting motions, and the permitted p x v values are also higher in the pivoting application.

Figure 10.3: Maximum recommended surface pressure dependent on the temperature

Temperatures

The short-term permitted maximum application temperature is +300°C. The pressure resistance of iglidur® A500 plain bearings declines with increasing temperatures. Fig. 02 clarifies this connection. The temperatures prevailing in the bearing system also have an influence on the bearing wear.

Figure 2.4: Coefficients of friction dependent on the surface speed, p = 0.75 MPa

Figure 05: Coefficients of friction dependent on the load, v = 0,01 m/s

X = Load [MPa]
Y = Coefficient of friction μ

Friction and wear

The coefficient of friction is dependent on the load that acts on the bearing (Fig. 04 and 05).

Coefficients of friction for iglidur® A500 against steel
(Ra = 1 µm, 50 HRC)

iglidur® A500	Dry	Grease	Oil	Water
Coefficients of friction µ	0,26 - 0,41	0,09	0,04	0,04

Figure 06: Wear, rotating application with different shaft materials, p = 1 MPa, v = 0.3 m/s
 
X = shaft materials
Y = wear [μm/km]
 
A = Aluminum, hard-anodized
B = machining steel
C = Cf53
D = Cf53, hard chrome-plated
E = St37
F = V2A
G = X90

Shaft materials

The Fig. 06 displays a summary of the results of tests with different shaft materials conducted with plain bearings made of iglidur® A500. The combination "iglidur® A500/hard-chromed shaft" clearly stands out in rotating application. Up to about 2.0 MPa, the wear of this combination remains largely independent of load. In pivoting motions with CF53 shafts, the wear resistance is better than in rotations under equal load. Please contact us in case the shaft material scheduled by you is not included in these figures.

Medium	Resistance
Alcohols	+
Hydrocarbons	+
Greases, oils without additives	+
Fuels	+
Diluted acids	+
Strong acids	+
Diluted bases	+
Strong bases	+

+ resistant      0 limited resistance      - not resistant
All specifications at room temperature[20 °C]
Table 05: Chemical resistance of the iglidur® bearings A500

Electrical properties

Specific forward resistance	> 1014 Ωcm
Surface resistance	> 1013 Ω

Chemical resistance

iglidur® A500 bearings have an excellent resistance to cleaning agents, fats, oils, alkalis and acids.
 

Radioactive rays

Bearings made of iglidur® A500 figure among the most radiation-resistant bearings in the iglidur® product range. The bearings are resistant up to a radioactive intensity of 2 x 10⁵ Gy Higher radiations affect the material and can lead to the loss of important mechanical properties.

UV-resistant

iglidur® A500 bearings are largely resistant to UV rays.

Vacuum

The iglidur® A500 bearings can be used in vacuum only restrictedly.

Electrical properties

iglidur® A500 bearings are electrically insulating.

Maximum moisture absorption
by +23 °C/50 % r. F.	0,3 weight-%
Max. water absorption	0,5 weight-%

Table 06: Humidity absorption of iglidur® A500

Diagram 10: Effect of moisture absorption
 
X = Moisture absorption [weight %]
Y = Reduction of inside diameter [%]

humidity absorption / moisture absorption

The humidity absorption of the iglidur® A500 bearings amounts to just 0.5% with saturation in water.

Important tolerances for iglidur® A500 bearings according to ISO 3547-1 after the press-fit.

Diameter d1 [mm]	Shaft h9 [mm]	iglidur® A500 F10 [mm]	Housing H7 [mm]
Up to 3	0 - 0,025	+0,006 +0,046	0 +0,010
> 3 to 6	0 - 0,030	+0,010 +0,058	0 +0,012
> 6 to 10	0 - 0,036	+0,013 +0,071	0 +0,015
> 10 to 18	0 - 0,043	+0,016 +0,086	0 +0,018
> 18 to 30	0 - 0,052	+0,020 +0,104	0 +0,021
> 30 to 50	0 - 0,062	+0,025 +0,125	0 +0,025
> 50 to 80	0 - 0,074	+0,030 +0,150	0 +0,030

Table 07: Important tolerances iaw. ISO 3547-1 after press-fitting.

Installation tolerances

iglidur® A500 bearings are standard bearings for shafts with h-tolerance (recommended minimum h9).

After the installation in a housing bore with H7 tolerance, the inner diameter of the bearing automatically adjusts to the E10 tolerance.